Classified

[Golear]

I have a dust cover that will fit a VPI Classic, in good condition. $100. I'm in Portland, Oregon.

[thegage]

About eight months old with light use. I bought it to use with other parts to build up a player for a second system but I don't really use it and I don't run multiple cartridges in my main system, so I'm selling to use funds elsewhere.

Wiring is what was standard at the time of purchase, non-integral finger lift, 160gm counter-weight, and it has a counter-intuitive installed on the weight. A couple of very faint marks on the top of the headshell from cartridge installation, but otherwise in excellent condition.

NOTE: This tonearm is supplied with smaller side weights because it was used with an older VTA-on-the-fly tower (bigger weights won't clear the side of older towers). It didn't matter to me because I used a second pivot. If the smaller weights matter to you it's a good excuse to buy the second pivot, which makes a noticeable improvement.


John K.

JMW 3D.jpg

JMW Weight.jpg

Maybe this will spur more interest: Adding the VTA-on-the-fly base for a package. Includes the tonearm, base, Anti-Skate, and 2nd pivot. (Note: picture shows older tonearm rest, but will include correct rest for the 3D arm.)

Tonearm Base.jpg

Someone really should snap these up.

Reduced to $1800 shipped.

[Packgrog]

A couple of modest items that I have available and need to offload to fund a replacement cartridge:

https://www.usaudiomart.com/details/649 ... arms-120g/
https://www.usaudiomart.com/details/649 ... cable-07m/

[miner]

***SOLD***

Bought new 4 months ago, for spare JMW3D arm which I recently sold. This cartridge has never been used. $3900. Purchased from VPI when they were offered on the site.

Harry/VPI sent me a new A95 to replace my original with a slightly skewed cantilever.

[thegage]

About eight months old with light use. I bought it to use with other parts to build up a player for a second system but I don't really use it and I don't run multiple cartridges in my main system, so I'm selling to use funds elsewhere.

Wiring is what was standard at the time of purchase, non-integral finger lift, 160gm counter-weight, and it has a counter-intuitive installed on the weight. A couple of very faint marks on the top of the headshell from cartridge installation, but otherwise in excellent condition.

NOTE: This tonearm is supplied with smaller side weights because it was used with an older VTA-on-the-fly tower (bigger weights won't clear the side of older towers). It didn't matter to me because I used a second pivot. If the smaller weights matter to you it's a good excuse to buy the second pivot, which makes a noticeable improvement.


John K.

JMW 3D.jpg

JMW Weight.jpg

Maybe this will spur more interest: Adding the VTA-on-the-fly base for a package. Includes the tonearm, base, Anti-Skate, and 2nd pivot. (Note: picture shows older tonearm rest, but will include correct rest for the 3D arm.)

Tonearm Base.jpg

Someone really should snap these up.

Reduced to $1800 shipped.

SOLD!

[Golear]

I have a dust cover that will fit a VPI Classic, in good condition. $100. I'm in Portland, Oregon.

Sold.

[aztwang]

Dust cover that fits VPI Classic 3 and probably other classics too. Great condition!!

$140.00 plus shipping...

I'm out of Phx, AZ

Cheers...Don. WITHDRAWN

[miner]

I have for sale a Soundsmith Counterintuitive . Leftovers from my JMW 3D trade-in towards the Fatboy. $30 for the SSCI. Buyer pays fees and shipping.

[aztwang]

Miner

Do you still have the Dr. Feikert protractor??

Thank you

Don

[miner]

***SOLD***

Don,
Still have the protractor - I send you an email.

kevin