HW 19 MK 3 platter upgrade

HW 19 MK 3 platter upgrade

Postby Handinglove » Thu Nov 29, 2018 5:52 pm

Hey everyone I am thinking about upgrading my platter from the mk3 to the mk4. I am noticing that the MK4 platter jpgradeonly weighs 2 pounds 4 ounces more than what I have. Is it the aluminum that makes the difference? I thought there would have been a bigger difference in weight.
Handinglove
Jr. Member
 
Posts: 10
Joined: Thu Oct 25, 2018 7:01 pm

Re: HW 19 MK 3 platter upgrade

Postby Brf » Fri Nov 30, 2018 8:42 am

There is a lot more than just the weight difference between the Mk3 and Mk4 platter. The Mk4 has a much more superior bearing plus it has the tri-point bearing/platter interface. The platter construction between the two platters is also different. The Mk3 is single layered acrylic platter with a lead ring insert whereas the Mk4 is a multi-layered acrylic platter with a lead insert which improves the platter's damping properties.

IMHO and IME, the Mk4 is a substantial upgrade. Also, if you decide to go for the Mk4 platter, you will need the thicker arm board or a tonearm spacer to account for the taller platter.
User avatar
Brf
Site Admin
 
Posts: 3606
Joined: Tue Aug 26, 2014 9:23 am

Re: HW 19 MK 3 platter upgrade

Postby Handinglove » Fri Nov 30, 2018 3:28 pm

I was looking at the mk3 to mk4 upgrade from exclusive disk. It looks to be an aluminum platter. Are they selling a MK4 platter?
Handinglove
Jr. Member
 
Posts: 10
Joined: Thu Oct 25, 2018 7:01 pm

Re: HW 19 MK 3 platter upgrade

Postby spinblackcircle » Fri Nov 30, 2018 4:35 pm

Handinglove wrote:I was looking at the mk3 to mk4 upgrade from exclusive disk. It looks to be an aluminum platter. Are they selling a MK4 platter?


That's basically the Scout 1.1 platter. It's not the Mk4 platter. If you are patient, you can find these occasionally for about $300 as Scout owners upgrade to the Classic platter.

The platter BRF was describing looks like this:

Capture.JPG
Capture.JPG (22.65 KiB) Viewed 220 times
VPI Prime/Grado Reference Master, VPI 16.5 RCM, Audio Research LP1, Audio Research VSI60, Martin Logan Electromotion ESL, ClearDay and Audio Sensibility Cables
User avatar
spinblackcircle
Senior Member
 
Posts: 613
Joined: Wed Nov 05, 2014 3:09 pm
Location: Boston, MA

Re: HW 19 MK 3 platter upgrade

Postby Brf » Fri Nov 30, 2018 5:32 pm

The platter above is a latter production TNT platter.

The HW19 Mk4 platter looks like this
Attachments
B4D82C2F-C890-42AD-9B4B-D8D7CFFD1627.jpeg
B4D82C2F-C890-42AD-9B4B-D8D7CFFD1627.jpeg (66.85 KiB) Viewed 211 times
User avatar
Brf
Site Admin
 
Posts: 3606
Joined: Tue Aug 26, 2014 9:23 am

Re: HW 19 MK 3 platter upgrade

Postby Handinglove » Fri Nov 30, 2018 11:23 pm

20181130_222104.jpg
20181130_222104.jpg (2.7 MiB) Viewed 190 times

So my platter looks like it is an MK4 it weighs 10 pounds.
Handinglove
Jr. Member
 
Posts: 10
Joined: Thu Oct 25, 2018 7:01 pm

Re: HW 19 MK 3 platter upgrade

Postby Handinglove » Fri Nov 30, 2018 11:26 pm

20181130_222530.jpg
20181130_222530.jpg (2.27 MiB) Viewed 190 times
Handinglove
Jr. Member
 
Posts: 10
Joined: Thu Oct 25, 2018 7:01 pm

Re: HW 19 MK 3 platter upgrade

Postby bdp24 » Sat Dec 01, 2018 7:17 am

handinglove, your platter is the version that came on the HW-19 Mk.2 and Mk.3---an approximately 3/4" thick Delrin disc with a layer of lead inset into it's bottom, then covered with a thin layer of cork. The HW-19 Mk.4 platter was the same, only thicker (1.5" I believe), as brf's photo of one shows. The platter you are interested in is not an HW-19 platter (though it can be installed on one), it's from the Scout table. To be able to use the Scout platter on an HW-19, the 1" bearing housing hole in the 19's floating sub-chassis must be enlarged to accommodate the larger (1.25"?) hole required by the Scout's bearing housing.

Another option is to patiently wait for an Aries 1 platter & bearing to come up for sale. That platter is one some VPI owners prefer to the all-aluminum platters, and is comprised of a 3/8" top layer of Delrin combined with a 7/8" bottom layer of aluminum with a lead insert, covered in cork. That platter came with a 1" threaded stainless steel bearing housing, therefore requires no drilling of the HW-19's sub-chassis to install. That's what I did, and couldn't be happier. They sell (second-hand only, of course) for no more than a new Scout platter, so the choice is yours.

By the way, the platter spinblackcircle posted a pic of is from the TNT-5, and is comprised of a 3/4" top layer of Delrin and a 5/8" bottom layer of stainless steel, with no lead insert. The TNT-1 had the same platter as the HW-19 MK.4, the TNT-2, -3, and -4 the same platter as the Aries 1. Some of the TNT-2, -3, and -4 bearing housings were the 1" threaded stainless steel version found on the Aries 1, some were 1.25" aluminum with 3 holes in the housing's flange for mounting screws. Confusing, ain't it?!
bdp24
Member
 
Posts: 82
Joined: Tue Oct 06, 2015 7:22 am

Re: HW 19 MK 3 platter upgrade

Postby Handinglove » Sat Dec 01, 2018 8:25 am

Thank you everyone for the information. It was confusing but it has been made clearer. I will look for the Aries platter wish me luck. I am guessing they don't come up for sale very often. Happy spinning everyone.
Handinglove
Jr. Member
 
Posts: 10
Joined: Thu Oct 25, 2018 7:01 pm


Return to Support Forum

Who is online

Users browsing this forum: No registered users and 4 guests

x