Page 61 of 68

For sale: dustcover for VPI Classic

PostPosted: Fri Oct 05, 2018 7:13 pm
by Golear
I have a dust cover that will fit a VPI Classic, in good condition. $100. I'm in Portland, Oregon.

Re: FS: JMW 3D 10" Tonearm Wand and Base

PostPosted: Mon Oct 08, 2018 4:26 pm
by thegage
thegage wrote:
thegage wrote:About eight months old with light use. I bought it to use with other parts to build up a player for a second system but I don't really use it and I don't run multiple cartridges in my main system, so I'm selling to use funds elsewhere.

Wiring is what was standard at the time of purchase, non-integral finger lift, 160gm counter-weight, and it has a counter-intuitive installed on the weight. A couple of very faint marks on the top of the headshell from cartridge installation, but otherwise in excellent condition.

NOTE: This tonearm is supplied with smaller side weights because it was used with an older VTA-on-the-fly tower (bigger weights won't clear the side of older towers). It didn't matter to me because I used a second pivot. If the smaller weights matter to you it's a good excuse to buy the second pivot, which makes a noticeable improvement.


John K.

JMW 3D.jpg


JMW Weight.jpg


Maybe this will spur more interest: Adding the VTA-on-the-fly base for a package. Includes the tonearm, base, Anti-Skate, and 2nd pivot. (Note: picture shows older tonearm rest, but will include correct rest for the 3D arm.)


Tonearm Base.jpg


Someone really should snap these up.

Reduced to $1800 shipped.

Re: Classified

PostPosted: Mon Oct 08, 2018 4:40 pm
by Packgrog
A couple of modest items that I have available and need to offload to fund a replacement cartridge:

https://www.usaudiomart.com/details/649 ... arms-120g/
https://www.usaudiomart.com/details/649 ... cable-07m/

SOLD: Unused Ortofon A95 MC cartridge

PostPosted: Wed Oct 10, 2018 2:09 pm
by miner
***SOLD***

Bought new 4 months ago, for spare JMW3D arm which I recently sold. This cartridge has never been used. $3900. Purchased from VPI when they were offered on the site.

Harry/VPI sent me a new A95 to replace my original with a slightly skewed cantilever.

Re: FS: JMW 3D 10" Tonearm Wand and Base

PostPosted: Thu Oct 11, 2018 1:52 pm
by thegage
thegage wrote:
thegage wrote:
thegage wrote:About eight months old with light use. I bought it to use with other parts to build up a player for a second system but I don't really use it and I don't run multiple cartridges in my main system, so I'm selling to use funds elsewhere.

Wiring is what was standard at the time of purchase, non-integral finger lift, 160gm counter-weight, and it has a counter-intuitive installed on the weight. A couple of very faint marks on the top of the headshell from cartridge installation, but otherwise in excellent condition.

NOTE: This tonearm is supplied with smaller side weights because it was used with an older VTA-on-the-fly tower (bigger weights won't clear the side of older towers). It didn't matter to me because I used a second pivot. If the smaller weights matter to you it's a good excuse to buy the second pivot, which makes a noticeable improvement.


John K.

JMW 3D.jpg


JMW Weight.jpg


Maybe this will spur more interest: Adding the VTA-on-the-fly base for a package. Includes the tonearm, base, Anti-Skate, and 2nd pivot. (Note: picture shows older tonearm rest, but will include correct rest for the 3D arm.)


Tonearm Base.jpg


Someone really should snap these up.

Reduced to $1800 shipped.


SOLD!

Re: For sale: dustcover for VPI Classic

PostPosted: Fri Oct 12, 2018 12:50 am
by Golear
Golear wrote:I have a dust cover that will fit a VPI Classic, in good condition. $100. I'm in Portland, Oregon.


Sold.

Re: Classified

PostPosted: Mon Oct 15, 2018 1:33 pm
by aztwang
Dust cover that fits VPI Classic 3 and probably other classics too. Great condition!!

$140.00 plus shipping...

I'm out of Phx, AZ

Cheers...Don. WITHDRAWN

FS: SSCI and dual pivot

PostPosted: Mon Oct 22, 2018 2:34 pm
by miner
I have for sale a Soundsmith Counterintuitive . Leftovers from my JMW 3D trade-in towards the Fatboy. $30 for the SSCI. Buyer pays fees and shipping.

Re: Classified

PostPosted: Thu Oct 25, 2018 1:06 am
by aztwang
Miner

Do you still have the Dr. Feikert protractor??

Thank you

Don

Re: Classified

PostPosted: Thu Oct 25, 2018 10:46 am
by miner
***SOLD***

Don,
Still have the protractor - I send you an email.

kevin